top of page

How to Keep Water Out of a Metal Building at the Slab Edge

Writer: Ridgeline Structures
Ridgeline Structures
3 days ago
3 min read

The morning after a hard rain, you find a wet strip along the inside wall of your metal garage. The roof may be doing its job, but rain can run down the siding, land on exposed concrete, and work its way under the base rail—the horizontal steel tube that anchors the wall frame to the slab. That path is especially worth checking if the concrete extends beyond the wall.


Three details can help keep that water outside. Base rail sealant closes small gaps where steel meets concrete. Rat guard closes off the bottom of the siding and, depending on its profile, helps direct runoff outward. A concrete drip ledge lets the siding extend below the slab edge so rain can shed below the rail-to-slab joint.


BASE RAIL SEALANT CLOSES THE GAP UNDER THE FRAME


Cutaway of foam sealant tape compressed between a steel base rail and a concrete slab, beside a photo of a Sika EMSEAL AST Hi-Acrylic tape roll.

Even a slab that looks smooth can have small low spots where it meets a straight steel rail. One way to seal that joint during installation is with a precompressed foam tape, such as Sika EMSEAL AST Hi-Acrylic. The installer applies the tape beneath the rail before setting and anchoring the frame. The foam expands into small irregularities. The tape has to be sized for the joint because its ability to resist water depends on how much it’s compressed.


If the building is already up and you’ve traced the leak to the rail-to-slab joint, an exterior-grade sealant compatible with concrete and galvanized steel may be an option where the joint is accessible. If there’s a puddle against the wall after every storm, address where that water is coming from and give it a way to drain.


RAT GUARD FINISHES THE BOTTOM OF THE SIDING


Rat guard trim shown as a folded metal piece, an end profile, and installed below ribbed metal wall panels at a concrete slab.

Rat guard is formed metal trim installed along the bottom of the wall panels. It helps close openings where rodents can get in. A profile with an outward drip lip can also guide rain off the siding, especially where the trim can discharge past the slab edge. Ask to see the actual profile and where its lip will land. On a wide, flat slab, water can drip off the trim and still land on concrete beside the wall. The joint under the base rail may need its own seal.



A CONCRETE DRIP LEDGE LETS THE SIDING SHED WATER BELOW FLOOR LEVEL


Section drawing of a step down at the edge of a concrete slab, beside a jobsite photo of a formed drip ledge around a new slab.

A drip ledge, also called a sheeting ledge or slab notch, is a formed step down at the outside edge of the concrete. The base rail sits on the higher surface, and the siding extends down past the top of the slab. That gives rain running down the wall a path to the outside below the joint where the rail meets the concrete. The ledge needs a way to drain so water has somewhere to go after it leaves the siding.


Work out this detail before the concrete is poured. Have your building supplier and concrete contractor review the same drawing so they agree on where the rail sits, where the siding ends, and how the ledge meets the garage door opening or an adjoining apron. Use the dimensions for your building and foundation.


WHAT TO ASK BEFORE YOU POUR OR BUILD


  • Pouring a new slab? Ask for the manufacturer’s slab-edge detail before the concrete crew sets the forms. Find out whether the siding will hang past the edge or land over a formed drip ledge.


  • Building on an existing slab? Tell your project manager how far the concrete extends past the proposed walls and where water collects after a storm. Ask how the rail-to-slab joint will be sealed and where the wall trim will discharge.


  • Adding a driveway or lean-to slab? Check where runoff will go at the shared wall and the roll-up door. The door threshold has its own water path, so include it in the drainage plan.


Planning a metal garage or workshop? Check out designs or draw up your own. Our project managers are available to answer any questions you may have: 336-612-3000.


Talk with your project manager before you pour. If the slab is already in place, send photos of its edges and, if you can, where water sits after a rain. That gives us a starting point for talking through the base rail seal, wall trim, and slab edge before installation.

 
 
 

Comments


bottom of page